3Dconnexion input devices/ro

Linux

FreeCAD supports drivers from project Spacenav. This is a project aiming to create an open-sourced driver which is compatible with the proprietary drivers from 3Dconnexion.

Ubuntu

sudo apt-get install spacenavd

Note, however, that version 0.6 available on Ubuntu 20.04 (and probably older ones) does not seem to work. You then have to compile spacenavd from source as explained below.

Fedora

sudo yum install spacenavd

Debian

apt-get install spacenavd libspnav-dev

Spacenav needs these permissions:

cp ~/.Xauthority /root/

Restart spnavd and FreeCAD

/usr/bin/spnavd_ctl x11 stop
/usr/bin/spnavd_ctl x11 start

openSUSE

sudo zypper install spacenavd

This is recommended if your distribution might provide an outdated version.

./configure
make

make install
./setup_init
/etc/init.d/spacenavd start

• Aceasta instalează daemonul spacenav, configurează-l să se încarce automat în boot-ul sistemului și pornește daemonul fără a trebui să repornească.
• Acum este timpul să verificați dacă dispozitivul dvs. este detectat corespunzător. Cu dispozitivul deconectat, executați următoarea comandă și apoi conectați-l.

tail -n100 -f /var/log/spnavd.log

Dacă ieșirea arată cam așa, puteți continua.

Device detection, parsing /proc/bus/input/devices
trying alternative detection, querying /dev/input/eventX device names...
  trying "/dev/input/event1" ... Power Button
  trying "/dev/input/event2" ... 3Dconnexion SpaceNavigator
using device: /dev/input/event2
device name: 3Dconnexion SpaceNavigator

./configure
make

• Dacă eșuează cu următoarea eroare: ...

fatal error: gtk/gtk.h: No such file or directory

• ... atunci trebuie să instalați libgtkmm-2.4-dev. Sub Ubuntu, aceasta se face astfel:

sudo apt-get install libgtkmm-2.4-dev

• Când s-a terminat cu succes, executați următoarea comandă 'ca root' (sau prefix cu sudo.)

make install

• Urmați același model pentru a compila și instala spnavcfg. Asigurați-vă că rulați spnavcfg ca root, sau altfel nu vor fi salvate setări!

Starting spacenavd as a systemd service at boot

If you want to start spacenavd at boot using systemd, do the following:

• Go to the directory where you clone the spacenavd repository (to the root of the repository)
• "sudo cp contrib/systemd/spacenavd.service /usr/lib/systemd/system/spacenavd-local.service".
• "sudo systemctl enable spacenavd-local.service".
• "sudo systemctl start spacenavd-local.service", if you want to start it right away.

This is only necessary for the installation from source.

If sometimes SpaceNavigator stops working, it is good to restart driver. To restart it, go to Terminal and execute:

sudo xhost +
sudo /etc/init.d/spacenavd restart

După aceea, reporniți FreeCAD. La unele distro-uri este necesar ca la fiecare boot.

Known Issues

A user reported on the forum they saw the following:

 Spacenav daemon 0.6
 failed to open config file /etc/spnavrc: No such file or directory. using defaults.
 adding device.
 device name: 3Dconnexion SpacePilot
 using device: /dev/input/event5
 No protocol specified
 failed to open X11 display ":0.0" 

The workaround that worked for them:

sudo cp ~/.Xauthority /root/
sudo spnavd_ctl x11 start
sudo systemctl restart spacenavd

3Dconnexion input devices are supported on macOS, provided FreeCAD is built and used on a system with the 3Dconnexion drivers installed. You may need 3DxWare 10.7.2 or greater for macOS 12 Monterey.

As of version 0.13, 3D mouse is supported under Windows. You need to have 3Dconnexion drivers installed. In FreeCAD version 1.0 a new integration with 3Dconnexion devices has been introduced. If compiled with that integration, only recent hardware is supported: to support older devices users will need to self-compile with the FREECAD_3DCONNEXION_SUPPORT cMake variable set to "Raw Input". Windows users should be aware that 3Dconnexion's driver (not the code in FreeCAD) contains a telemetry package that communicates information about your installed software back to 3Dconnexion.

Known Issues

• In FreeCAD version 1.0 and later changing settings in the 3DX config window may not have the expected results (issue). To fix this:
  1. Stop the driver (by running Stop 3DxWare).
  2. Go to ..<user>\AppData\Roaming\3Dconnexion\3DxWare\Cfg and delete the FreeCAD.xml file.
  3. Start the driver (by running Start 3DxWare).
  4. Run FreeCAD and check if you can change the Spaceball Motion settings.

version 1.0 and above: The 3Dconnexion manipulator can be set up in its driver app (3DxWare software).

version 0.21 and below: If a Spaceball is detected the following tabs in the Customize dialog can be used to change settings:

In this tab you have ability to set up some of general space mouse settings. They include:

• Global Sensitivity - Slider with ability to set global sensitivity
• Dominant - if you enable dominant mode, only axes with highest move will be considered
• Flip YZ - This option enables you to flip Y and Z axes on 3D mouse
• Enable Translations - easy way to enable/disable translations
• Enable Rotations - easy way to enable/disable rotations
• Calibrate - enables you to calibrate space navigator. It is pressed while space navigator is not moved.
• Set To Default - removes all settings and sets them to default.

În afară de aceasta, pentru fiecare axă aveți posibilitatea de a seta:

• Activat - Activați / Dezactivați axele
• Reverse - Mișcarea inversă pe axe
• Sensibilitate - cursor cu capacitatea de a seta sensibilitatea

When you open this tab for the first time, it will be empty and unavailable. To activate it, you must press one of your space mouse buttons. After you do, list of buttons will appear on the left side, and list of commands will be available on the right side.

Pentru a conecta anumite comenzi cu un buton, selectați butonul din partea stângă și este comanda pe partea dreaptă. Pentru a șterge comenzile de la buton, apăsați "Șterge".

Troubleshooting

Check if your FreeCAD installation links to the spacenav library. The best way to check this is by running FreeCAD from the command line terminal FreeCAD --log-file /tmp/freecad.log and close it immediately again. Then open the file /tmp/freecad.log and search for the messages:

Connected to spacenav daemon

or

Couldn't connect to spacenav daemon. Please ignore if you don't have a spacemouse.

If none of them appears then your FreeCAD build doesn't link to the spacenav library. If the former message appears then it basically works. The latter message means there is probably a problem with the spacenav daemon.

Related

• Forum thread spacenav on Windows
• Forum thread Space navigator axis confusion